Measure the route, not the gap between units
The right RCA amp cable length is the distance your signal actually travels, not the straight-line gap between the head unit and the amplifier. Before you compare a 1 m, 2.5 m or 5.5 m lead, sketch the route the cable will take: from the rear of the source, along the sill or under trim, around any seat or crossover, and into the amp's input side.
Add the slack you need to remove the source or amp later without pulling on the connectors, and add the extra for any loop around an obstacle. A lead that only just reaches is harder to route cleanly and leaves no room for service. A lead that is far too long invites coils you then have to manage. The goal is a route that reaches with a little spare, not a specific number of centimetres.
A practical order for choosing the length
- 1. Confirm you need a two-channel lead: All three Audison BT2 leads here are two-channel interconnections. Count the channels your source-to-amp link needs before you think about length; a two-channel lead suits a single stereo pair, not a multi-channel run.
- 2. Trace the full path with a tape or string: Run a length of string along the intended route, following the same corners and trim the cable will follow. Measure the string, then compare it with the supplied lead lengths of 1 m/3.3 ft, 2.5 m/8.2 ft and 5.5 m/18 ft.
- 3. Keep signal and power routes apart: The BT2 leads use twisted-pair balanced conductors and cascaded dual aluminium shielding to reject interference, but shielding works best when you do not lay the signal lead tight against power cable. Plan the route with separation where the car allows it.
- 4. Leave service slack at both ends: The connectors are machined metal with a tug-proof sealed internal connection. That reliability is only useful if the cable is not under tension, so leave enough slack to unplug and reconnect without straining the plug or the socket.
- 5. Buy the shortest length that completes the route: Once the route is measured, choose the shortest supplied length that still gives you service slack. That keeps excess cable out of the cabin and reduces the amount you have to coil and secure.
1 m, 2.5 m and 5.5 m: what each BT2 lead is for
The three Audison BT2 leads share the same construction and differ mainly in reach. Use the supplied lengths as the starting point, then match the lead to the route you measured.
- BT2 100 — 1 m/3.3 ft: Best suited to a short, direct run where the source and amplifier sit close together and the cable does not have to travel far through the car. Check that 1 m still leaves service slack at both ends before committing.
- BT2 250 — 2.5 m/8.2 ft: A middle length for installs where the source and amp are in different areas but the route is not a full front-to-rear run. Measure before assuming it will reach.
- BT2 550 — 5.5 m/18 ft: The long option for routes that cross more of the vehicle, such as a source at the front and an amplifier mounted toward the rear. Extra length still needs managing, so plan where the surplus will sit.
What the BT2 leads share, whatever length you choose
- Connection Best BT2 100 1.0m 3.3 ft 2 Channel Car RCA Amp Cable Lead: Two channel, Competition Grade Interconnection, 1 m/3.3 ft. Confirms the short lead is a two-channel interconnect, so it fits a single stereo source-to-amp link rather than a multi-channel setup.

Connection Best BT2 100 1.0m 3.3 ft 2 Channel Car RCA Amp Cable Lead - Connection Best BT2 250 2.5m 8.2 ft 2 Channel Car RCA Amp Cable Lead: Two channel, Competition Grade Interconnection, 2.5 m/8.2 ft. The middle length is the one to check against a measured route when neither the shortest nor longest lead looks right.

Connection Best BT2 250 2.5m 8.2 ft 2 Channel Car RCA Amp Cable Lead - Connection Best BT2 550 5.5m 18 ft 2 Channel Car RCA Amp Cable Lead: Two channel, Competition Grade Interconnection, 5,5 m/18 ft. The longest supplied lead covers routes that cross more of the vehicle, but the extra length has to be routed and secured.
Construction details that affect how you run the cable
All three BT2 leads use a SOFT TOUCH matt black jacket described as extremely flexible, with a polyamide polymer inner jacket protecting the inner conductors. That flexibility helps on routes with bends, but it does not remove the need to avoid sharp edges and tight kinks. Route the cable where trim will not pinch it.
The shielding is described as 110% twisted Mylar and double aluminium, with cascaded dual aluminium shielding to eliminate radiated interference. The WTPM winding twisted pair balanced conductors are intended to reject low-frequency electro-magnetic fields, and the lead is rated at over 100 dB noise rejection. Those are reasons to keep the signal route sensible, not a licence to run it alongside power cable.
Each lead also includes an extended remote turn-on wire, described as a built-in remote conductor for ease of installation. If you plan to use it, account for it in the same route and leave it accessible at both ends. The supplied information does not specify connector dimensions, so check the physical fit of the plugs against your equipment before ordering.
Checkpoints before you order
- Route measured, not estimated: Compare your measured string length with the supplied 1 m, 2.5 m and 5.5 m options, then pick the shortest that reaches with slack.
- Channel count confirmed: All three BT2 leads are two-channel. If your install needs more channels, these are not the right leads.
- Connector fit checked: The supplied information does not confirm plug dimensions or compatibility with specific head units or amplifiers, so verify the physical fit against your own equipment.
- Remote turn-on planned: The built-in remote conductor is part of the lead. Decide whether you will use it and route it accordingly.
- Surplus length managed: If the route needs less than the next length up, plan where the extra cable will sit so it does not loop near moving parts or heat sources.




