Voltar ao blog
Guias Práticos 2026-11-21 CEN 0 visualizações

How to Tune a Helix DSP with AMI Audio Measurement Interface

How to Tune a Helix DSP with AMI Audio Measurement Interface

Learn how to use the Audiotec Fischer AMI Tuning Kit for precise Helix DSP calibration, including signal analysis, automatic time measurement, and real-time tuning with the DSP PC-Tool.

Why the AMI Tuning Kit for Helix DSP Tuning

Tuning a Helix DSP demands accurate measurements of both electrical signals and acoustic output. The Audiotec Fischer AMI Audio Measurement Interface Tuning Kit is purpose-built for this task, integrating seamlessly with the DSP PC-Tool software. It combines a professional-grade measurement interface, a calibrated Beyerdynamic MM-1 microphone, and all necessary cables in one package, so you can start measuring without hunting for adapters or extra gear.

The kit supports USB-powered operation and works with Windows, macOS, Android, and iOS, making it a flexible choice for in-car or workshop use. Its key advantage is direct compatibility with Audiotec Fischer’s DSP PC-Tool, unlocking advanced features like the Advanced Input Signal Analyzer (AISA), Automatic Time Measurement (ATM), and Real-Time Analyzer (RTA) with the TuneEQ algorithm.

Key Components in the AMI Tuning Kit

Setting Up the AMI for Helix DSP Calibration

Connect the AMI to your computer via the supplied USB-C cable (USB-A adapter included if needed). The interface is USB-powered, so no external power supply is required. Then connect the AMI to your Helix DSP using the RCA or Toslink output for signal playback. Attach the Beyerdynamic MM-1 microphone to the AMI via the XLR cable and position it at the listening position (typically the driver’s headrest).

Launch the DSP PC-Tool software on your computer. The AMI is automatically recognized when connected. Select the measurement mode you need: RTA for frequency response analysis, AISA for input signal analysis, or ATM for automated time delay calibration.

  1. Connect hardware: Plug the AMI into your computer via USB, connect to the Helix DSP via RCA or Toslink, and attach the microphone via XLR.
  2. Open DSP PC-Tool: The software detects the AMI automatically. No driver installation is needed on Windows 10/11 or macOS.
  3. Select measurement mode: Choose RTA for real-time frequency response, AISA for input signal analysis (including factory EQ and allpass filters), or ATM for automated speaker delay calibration.

Using AISA for Input Signal Analysis

The Advanced Input Signal Analyzer (AISA) is one of the most powerful tools in the DSP PC-Tool when paired with the AMI. It lets you detect and correct factory-applied equalization curves, time alignment, and allpass filters present in the head unit’s output signal. This is especially useful when integrating an aftermarket DSP with a factory radio that applies its own processing.

To use AISA, connect the AMI’s line input to the head unit’s speaker or line-level output using the supplied RCA cable with RCA-to-Highlevel adaptors. The AMI’s dedicated line input has switchable sensitivity (max. 1 V or 40 V RMS), so you can measure both low-level preamp signals and high-level speaker outputs without distortion. Run the AISA routine in the software; the AMI will capture the signal and display any processing the factory radio applies.

Automated Time Measurement (ATM) for Speaker Delay

Automatic Time Measurement (ATM) uses the AMI and microphone to measure the acoustic arrival time from each speaker to the listening position. The software then calculates the correct time alignment values for your Helix DSP, saving you from manual delay calculations.

  1. Position microphone: Place the Beyerdynamic MM-1 at the driver’s headrest (or main listening position) using a mic stand or clamp.
  2. Run ATM in DSP PC-Tool: Select ATM mode; the software will play test tones through each channel and measure arrival times automatically.
  3. Apply calculated delays: The software populates the delay settings in the DSP. Verify with a quick RTA sweep to confirm coherence.

Real-Time Analyzer and TuneEQ for Frequency Response

With the AMI and microphone connected, the RTA mode displays a live frequency response graph in the DSP PC-Tool. You can play pink noise or the preloaded tuning tracks from the USB drive, then adjust EQ bands on your Helix DSP to flatten the response. The TuneEQ algorithm can automate this process: it measures the current response, calculates target EQ adjustments, and applies them to the DSP’s parametric EQ bands.

The AMI’s integrated loopback function enables advanced measurements like phase response analysis, which is helpful when aligning subwoofers with midbass drivers. The loopback sends a reference signal back to the interface, allowing the software to compare input and output for precise phase correction.

What the Supplied Information Confirms

Artigos relacionados

Customer Service
Início
Produtos
Carrinho
Perfil